Ryobi BTS16 Manuale Utente

OPERATOR’S MANUAL10 in. TABLE SAWBTS16SAVE THIS MANUAL FOR FUTURE REFERENCEYour table saw has been engineered and manufactured to our high standard fo

10FEATURESFig. 2PRODUCT SPECIFICATIONSBlade Arbor ...5/8 in.Blade Diameter ...

11KNOW YOUR TABLE SAWSee Figure 2.The safe use of this product requires an understanding of the information on the tool and in this operator’s manual

12FEATURESWARNING:Always remove the switch key when the tool is not in use and keep it in a safe place. In the event of a power failure, turn the swit

13The following tools (not included) are needed for assembly and making adjustments:TOOLS NEEDEDFEATURESBLADESFor maximum performance, it is recommend

14LOOSE PARTSThe following items are included with your table saw:Fig. 5ABCDEFGHKLIJMNPO A. Blade Guard with Spreader and Anti-Kickback Pawls ...

15UNPACKINGThis product requires assembly. Carefully remove the tool and any accessories from the box. Place it on a level work surface. NOTE: This

16ASSEMBLYMOUNTING THE TABLE SAW BASE TO THE QUICK STAND™ See Figure 8. Place the table saw base on the leg stand. Position the locking knob

17ASSEMBLYSMALL BLADE WRENCHLARGE BLADE WRENCHSLOTSFig. 13MOUNTING BRACKETWING SCREWTO INSTALL DUST BAGSee Figure 11.This dust bag hangs under the saw

18ASSEMBLYTO CHECK AND ALIGN THE SPREADER, SAW BLADE, AND BLADE GUARD ASSEMBLYSee Figure 14.If the blade guard assembly is out of alignment with

19ASSEMBLYOPERATIONWARNING:Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is suf-ficient to in

2TABLE OF CONTENTS Introduction ...

20PUSH BLOCKSPUSH STICKSFig. 17 Always use clean, sharp, and properly-set blades. Never make cuts with dull blades. To avoid pinching the blade, s

21OPERATIONBEVEL RIP CUT RIP CUTCROSS CUTMITER CUTCOMPOUND (BEVEL) MITER CUT BEVEL CROSS CUT1TYPES OF CUTSSee Figure 18.There are six basic cuts: 1) t

22Fig. 193/8 in. DIAMETER1/8 in. 1/4 in. 3/4 in. 3-5/8 in. 30°45°6 in. 8 in. 10 in. 12 in. 18 in. OPERATIONFEATHERBOARDA featherboard is a device

23OPERATIONTO CHANGE BLADE DEPTHSee Figure 21.The blade depth should be set so that the outer points of the blade are higher than the workpiece by app

24OPERATIONFRONT RAILFig. 24Fig. 25REAR LIPRIP FENCELOCKING LEVERSAW TABLEFig. 26LOCK KNOBMITER GAUGEWARNING:To reduce the risk of injury, always make

25OPERATIONTO USE THE SLIDING TABLE EXTENSIONSSee Figure 27.The sliding table extensions provide the operator with ad-ditional table width for support

26OPERATIONHEELING (PARALLELING) THE BLADE TO THE MITER GAUGE GROOVESee Figures 29 - 31.WARNING:The blade must parallel the miter gauge groove so the

27OPERATIONMAKING CUTSThe blade provided with the saw is a high-quality combina-tion blade suitable for ripping and cross cut operations.WARNING:Do no

28OPERATIONMAKING A RIP CUTSee Figure 34.It is recommended you make a test cut on scrap wood.WARNING:Make sure the blade guard assembly is inst

29OPERATION Stand to the side of the wood as it contacts the blade to reduce the chance of injury should kickback occur. Never stand directly in the

3WARNING:Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious perso

30OPERATIONMAKING A BEVEL RIP CUTSee Figure 38.It is recommended you make test cuts on scrap wood.WARNING:The rip fence must be on the right side of t

31OPERATION Set the saw blade to the correct depth.  Loosen the lock knob on the miter gauge, set the miter gauge to the desired angle and tighten

32OPERATIONMAKING A NON-THROUGH CUTSee Figure 41.Non-through cuts can be made with the grain (ripping) or across the grain (cross cut). The use of a n

33OPERATION Fig. 42DADO CUTMAKING A DADO CUTSee Figure 42.An optional dado throat plate (part number 0121010317) is required for this procedure. Do no

34WARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could result in seri

35ADJUSTMENTS Rotate the blade by hand to make sure it turns freely. Lower the saw blade and reinstall the throat plate. NOTE: Securely tighten t

36ADJUSTMENTSFig. 49BLADERIP FENCELOCKING LEVER1112131415163029SCREWSFig. 48LOCK NUTKNOBMITER GAUGE BASE45° ADJUSTABLE STOP SCREW0° ADJUSTABLE STOP SC

37WARNING:When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product dama

38Excess vibration.Rip fence does not move smoothly.Rip fence does not lock at rear.Cutting binds or burns work.Wood edges away from rip fence when ri

39TROUBLESHOOTING PROBLEM CAUSE SOLUTIONAdjust positive stops.Adjust the miter gauge.Clean the gears or screw post.Plug in motor cord or wall cord

4GENERAL SAFETY RULES work or around or over the blade while blade is rotating. Do not attempt to remove cut material when blade is moving.

987000-09310-28-08 (REV:03)OPERATOR’S MANUAL10 in. TABLE SAW BTS16WARNING:Some dust created by power sanding, sawing, grinding, drilling, and other co

5SPECIFIC SAFETY RULES NEVER perform any operation “freehand” which means using only your hands to support or guide the workpiece. Always use either

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Properinterpretation of t

7SYMBOLSThe following signal words and meanings are intended to explain the levels of risk associated with this product.DANGER:Indicates an imminently

8EXTENSION CORDSUse only 3-wire extension cords that have 3-prong ground-ing plugs and 3-pole receptacles that accept the tool’s plug. When using a po

9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Pilo