Ryobi P550 Manuale Utente

SAVE THIS MANUAL FOR FUTURE REFERENCEYour miter saw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation

10FEATURESCARRYING HANDLESee Figure 2.For convenience when carrying or transporting the miter saw from one place to another, a carrying handle

11SWITCH TRIGGERSee Figure 6.To prevent unauthorized use of your compound miter saw, remove battery pack and lock the switch in the off position. To l

12LOOSE PARTSWARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.n 8-1/4 in. Carbide

13ASSEMBLYUNPACKINGThis product requires assembly.n Carefully lift the saw from the carton by the carrying handle and the saw base, and plac

14ASSEMBLYDUST GUIDESee Figure 10.n Remove the battery pack from the tool.n Place the dust guide (end marked INSERT) over the exhaust port i

15ASSEMBLYPHILLIPS SCREWBLADE BOLT COVER4 53 01515304522.531.6222. 531.62ROTATIONFig. 13LOWER BLADEGUARD BRACKETFig. 14LOWER BLADE GUARDNOTCHPHILLIPS

16ASSEMBLY�n Replace outer blade washer. The double “D” flats on the blade washers align with the flats on the spindle. �n Depress spindle lock butt

17ASSEMBLYWARNING:Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle lock

18ASSEMBLYSQUARING THE SAW BLADE TO THE FENCESee Figures 21 - 24.n Remove the battery pack from the tool.n Pull the saw arm all the way down and eng

1945301501522.530454531.6222.531.62ASSEMBLYSQUARING THE BLADE TO THE MITER TABLESee Figures 25 - 28.n Remove the battery pack from the tool.n Pull t

2n Introduction ...

20LED FUNCTIONS OF CHARGERLED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK:n Red LED on = Fast charging mode.n Green LED on = Fu

21��OPERATIONred LED does not come on after 30 minutes, this mayindicate a defective battery pack a

22

23OPERATION4 53 01515304522.531.6222.531.62ROTATIONSTRAIGHTCROSSCUTFig. 34WORK CLAMPTO CROSSCUTSee Figure 34.A crosscut is made by cutting acros

24OPERATIONTO BEVEL CUTSee Figures 35 - 36.A bevel cut is made by cutting across the grain of the workpiece with the blade angled to

25OPERATIONFig. 37C-CLAMPCOMPOUND MITER CUTn Once the saw arm has been set at the desired angle, securely tighten the bevel lock knob.n Recheck

26OPERATIONn Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece w

27OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3

28OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes th

29OPERATIONWRONGWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against

3GENERAL SAFETY RULESWARNING!READ AND UNDERSTAND ALL INSTRUCTIONS. Fail-ure to follow all instructions listed below, may result in electric shock, fir

30ADJUSTMENTSWARNING:To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the tool when making

31MAINTENANCEWARNING:When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause p

RYOBI TECHNOLOGIES, INC.1428 Pearman Dairy Road, Anderson, SC 29625Post Office Box 1207, Anderson, SC 29622-1207Phone 1-800-525-2579www.ryobitools.com

4GENERAL SAFETY RULESn Hold tool by insulated gripping surfaces when per-forming an operation where the cutting tool may con-tact hidden wiring. Co

5n An extension cord should not be used unlessabsolutely necessary. Use of improper extension cord could result in a risk of fire and e

6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols wil

7SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we su

8GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Push

9FEATURESPRODUCT SPECIFICATIONSBlade Arbor ................ 5/8 in.Blade Diameter......